Friday, December 17, 2010

Insulation, Old School: Wax Impregnating Maple

Apologies for the long gap. We are back!

Here's a challenge. Making a good custom-built insulating panel in 1910, without use of asbestos, custom ceramics, or plastics.

The great minds of the age started with wood. Tests were done and it was found that maple, a hardwood, was the best combination of strength, workability and a natural insulator. Except, of course, when it was wet. And wood is always somewhat wet. If you dry it out entirely, it cracks, and in any case, reabsorbs moisture from the air over time.

The idea was struck to use paraffin wax to offset the water. But how? Even if you melt it on, there's still water within the wood.

Experiments were tried with VPI (vacuum pressure impregnation). In this, the unit is dipped in resin, set in a pressure vessel, and a vacuum is drawn. Water boils at about 75 degrees F in a vacuum, so it boils off, the vapor taken in by the vacuum pump. There is literally nothing in the voids, so when vacuum is released (and shop air pressure applied), the resin is sucked into the voids. It's a great theory, it works on metal machines like traction motors. But alas - not wood!

As it happens, liquid wax is happily above the boiling temperature of water. So of course, they had tried simply immersing the wood in hot wax. Above 212 degrees, the water boils off nicely, replaced not with a void, but water vapor. When it cools, this vapor condenses to a tiny amount of water, creating a vacuum that should draw in the wax. Assuming the wax had not turned solid!

In the early days of electric equipment, a great deal of testing had been done on this. They examined wax saturation and insulation quality. With help from the railway preservation community at large, BAERA volunteers had done some research on this.

It turns out there was a very particular pattern of temperature control that was required - heating to high temperature to drive off water, then a lower temperature to allow wax to absorb. The sequence took several hours.

It was within the range of a common (nowadays) electric skillet. The board barely fit! Here we see it at the end of the cycle, the wax re-frozen.

One might look at the picture and think: "OK! Turn it back on, come back in 20 minutes, and fish the board out of the wax!" No. After it was out, the wax would flow out of the wood. In fact, the board must be removed with the greatest care - the wax can be barely softened, and heated with spot heat from a "hair dryer" just enough to wipe the excess away.

The wood has already been machined (drilled). This was a product of careful and repeated fitting to the car. Even with the refinement of these techniques, wax impregnation is far from complete. Machining afterward would have exposed areas of poor penetration.

5 comments:

  1. Waterproofing wood parts was done for years by boiling the parts in raw linseed oil ...a much more stable finish

    ReplyDelete
  2. These details only reflect one approach to building a superinsulated building. insulation machines

    ReplyDelete
  3. This is a great inspiring article.I am pretty much pleased with your good work.You put really very helpful information. Keep it up. Keep blogging. Looking to reading your next post. attic insulation removal and replacement

    ReplyDelete
  4. This is excellent information. Thanks for sharing.
    AR Engineering is one of the leading manufacturers of industrial oil purification units for all types of oils used in industries today. industrial of industrial oil purification units, Industrial oil purification plants.

    Industrial Oil Purification Systems
    Oil Filtration & Cleaning Systems
    Portable Oil Filtration System
    Transformer Oil Filtration Plant
    Industrial oil purification plants
    Industrial Oil Filter Machine
    Industrial Oil Filters
    Transformer Oil Filtration System
    Transformer Oil Cleaning Systems

    ReplyDelete
  5. I will recommend anyone looking for Business loan to Le_Meridian they helped me with Four Million USD loan to startup my Quilting business and it's was fast When obtaining a loan from them it was surprising at how easy they were to work with. They can finance up to the amount of $500,000.000.00 (Five Hundred Million Dollars) in any region of the world as long as there 1.9% ROI can be guaranteed on the projects.The process was fast and secure. It was definitely a positive experience.Avoid scammers on here and contact Le_Meridian Funding Service On. lfdsloans@lemeridianfds.com / lfdsloans@outlook.com. WhatsApp...+ 19893943740. if you looking for business loan.

    ReplyDelete